WC flush plate for Prevista Visign for More 201 electronic
Product information
WC flush plate for Prevista Visign for More 201 electronic
for all Prevista concealed cisterns
| Year built (from): | 01-03-19 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Operators
Consumers
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
General notes
If you notice any damage on the product or individual components, do not carry out a repair. Instead, have the product replaced by qualified personnel.
This product is not intended for use by persons (including children) with restricted physical, sensory or mental aptitude or lack of experience and/or knowledge.
Make sure that children do not play with this product.
Symbols
Observe the symbol listed on the label:
Symbol | Description |
|---|---|
 | CE marking, Product Safety in Europe |
 | EAC marking, registration of products in the territory of the Customs Union |
 | Direct current |
 | Protection class III |
 | The marked product must not be disposed of as household waste. |
Product description
Overview
- 1 flush plate
- 2 Actuating rod
- 3 retaining bolt
- 4 silicon grease (2 x 2 g)
- 5 installation frame
Technical data
Flush volume
The flush volumes for the flush actuation are:
Small flush volume: approx. 2 / 3 / 4 litres
Large flush volume: approx. 3.5 / 4.5 / 6 / 7.5 litres
For the setting of the flush see Setting the flush .
Hygiene function
Hygiene flush volume |
|---|
Hygiene flush interval |
3 / 7.5 litres |
1 / 12 / 24 / 72 / 168 hours |
Voltage and current
Voltage [V] | Current [mA] |
|---|---|
6.5 | 1 |
Connection diagram
- 1 WC flush plate for Prevista
- 2 Electronic drive unit
- 3 Power pack
- 4 Plastic branch protection class II
Operating mode
Flushes from Prevista concealed cisterns are actuated electronically via the flush plate.
Optionally, a large or small flush volume can be flushed.
Viega Hygiene function
Stagnation can lead to the build up of germs (e.g. legionella) in potable water pipelines. It is important to rinse the pipeline regularly to prevent the build up of bacteria. The Viega Hygiene function was developed for this reason.
Flushes are actuated in a time-controlled manner with the Viega Hygiene function. Interval and flush volume will be set as required and saved by the control. All settings remain saved during a power cut.
The function is deactivated at the factory.
System expansions
The system's range of functions can be expanded through the connection of accessories onto the control.
Radio controlled actuation
You need the following accessories to connect a radio receiver instead of a cable-connected external sensor:
Signals to actuate the flush (e. g. on support hinged handles) sent by HEWI radio transmitters can be received by a radio receiver (model 8570.58).
Accessories
Required accessories
For complete mounting of the electronic flush plate, you need the electronic accessory set (model 8655.11). Install the mains adapter in a connection socket suitable for protection class II (e.g. model 8570.62).
This ensures installation according to SELV.
Optional accessories
WC installation frame with LED lighting (model 8650.1)
The WC installation frame with LED lighting is a backlit installation frame with proximity sensor.
Extension cable (model 8352.690)
2 metre cable for the extension of the power supply.
INFO!
Use a maximum of two extension cables with the mains adapter (4.75 meter total length).
Connection cable (model 8570.55)
3-meter cable for external flush actuation with on-site and commercially available buttons with closing function or potential-free contact (closing period 350 ms).
Extension cable adapter (model 8580.49)
For connection of a radio receiver.
Adapter (model 8570.57)
The battery compartment can be connected for a redundant power supply using the adapter (model 8570.56). The battery compartment is included in the adapter's scope of delivery.
WC remote flush actuation (models 8640.1 and 8641.1)
For electronic remote flush actuation on Prevista concealed cisterns.
Handling
Assembly
Prepare cistern
Requirements:
The accessory set electronic (model 8655.11) is mounted.
The cistern is fitted into the pre-wall.
The pre-wall is tiled.
-
Remove the shaft cover.
-
Cut into the corners of the revision shaft.
-
Fold the sides of the revision shaft outwards up to the tile level and snap them off.
Mounting the flush plate
-
Turn the site protection panel lock 90° anti-clockwise.
-
Remove the site protection panel.
-
Close the corner valve.
The maximum torque is 4 Nm.
-
Loosen the flexible hose on the filling valve.
-
Open the corner valve for a few seconds to flush the pipe.
-
Close the corner valve.
The maximum torque is 4 Nm.
-
Connect the flexible hose to the filling valve.
-
Re-open the corner valve.
-
INFO!
Check the corner valve and the filling valve for leak tightness.
INFO!
Set the desired flush volume, see Setting the flush .
-
Insert the site protection panel into the cistern.
-
Turn the site protection panel's lock by 90° clockwise.
-
Put on the installation frame.
-
Insert the retaining bolts.
-
Turn the retaining bolts by 90° in a clockwise direction.
-
Align the installation frame.
-
To fix the retaining pins, turn the safety rings in a clockwise direction.
INFO!
If you are not sure which cistern is installed, identify it by means of the following dimensions.
3H concealed cistern
Concealed cistern 3L
Concealed cistern 3F
For installation from the front into the concealed cisterns 3H, 3L, 3F.
-
Determine the distance for the actuating rod.
Cistern 3H and 3L.
-
If necessary, cut the actuating rod to length.
0: 75–50 mm
1: 50–25 mm
2: 25–10 mm
Cistern 3F.
-
If necessary, cut the actuating rod to length.
1: 75–55 mm
2: 55–35 mm
3: 35–15 mm
4: 15–10 mm
For installation from above into concealed cistern 3L.
-
Determine the distance for the actuating rod.
-
If necessary, cut the actuating rod to length.
0: 60–45 mm
1: 45–25 mm
2: 25–10 mm
-
Push the actuating rod through the left opening of the installation frame as far as it will go.
-
Align the actuating rod.
-
Turn the actuating rod clockwise by 90°.
-
Apply the silicon grease to the electronic connections.
-
Connect the control line to the flush plate.
-
If required, additional external sensors can be connected to the drive unit. See Connecting external sensors .
-
Mount the flush plate.
-
The flush plate is mounted.
Connecting external sensors
NOTICE!
Damage to property due to excess voltage
If you apply voltage to the connection cable for the external button, you will damage the control.
Do not apply any external voltage!
Requirements:
Button with locking function or potential-free contact (closure time at least 350 ms) available
Connection cable available
-
Connect the contact to actuate the small flush volume between the white (1) and yellow cable (3).
-
Connect the contact to actuate the large flush volume between the white (1) and green cable (2).
-
Strip the end of the brown cable (e.g., with a lustre terminal).
Commissioning
Setting the flush
INFO!
The smallest possible flush volume must be set at the drain valve in the cistern.
The small flush volume is set incorrectly.
The small flush volume is set correctly.
The flush volume is set via the DIP switch of the drive unit.
INFO!
Make the settings only in the currentless (unconnected) state.
- A Setting the flush volume
- B Interval of the Hygiene function
- C Setting the flush volume of the Hygiene function
- 0 DIP switch position: OFF
- 1 DIP switch position: ON
The assignment of the DIP switches:
Switches 1‑4 define the flush volume.
Switches 5‑7 define the interval of the Hygiene function.
Switch 8 defines the flush volume of the Hygiene function.
NOTICE!
Damage due to moisture
Risk of damage to the drive unit if moisture penetrates.
Do not remove the protective cover of the DIP switches.
Setting the flush volumes (A)
Program no. | Large flush volume (in litres) | Small flush volume (in litres) | Position of switches 1—4 | |||
|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | |||
Program 0 (factory setting) | 6 | 3 | 0 | 0 | 0 | 0 |
Program 1 | 3.5 | 2 | 0 | 0 | 0 | 1 |
Program 2 | 4.5 | 2 | 0 | 0 | 1 | 0 |
Program 3 | 6 | 2 | 0 | 0 | 1 | 1 |
Program 4 | 7.5 | 2 | 0 | 1 | 0 | 0 |
Program 5 | 3.5 | 3 | 0 | 1 | 0 | 1 |
Program 6 | 4.5 | 3 | 0 | 1 | 1 | 0 |
Program 7 | 7.5 | 3 | 0 | 1 | 1 | 1 |
Program 8 | 4.5 | 4 | 1 | 0 | 0 | 0 |
Program 9 | 6 | 4 | 1 | 0 | 0 | 1 |
Program 10 | 7.5 | 4 | 1 | 0 | 1 | 0 |
Enabling the Hygiene function and setting the intervals (B)
Interval (in hours) | Position of switches 5—7 | ||
|---|---|---|---|
5 | 6 | 7 | |
Switched off | 0 | 0 | 0 |
1 | 0 | 0 | 1 |
12 | 0 | 1 | 0 |
24 | 0 | 1 | 1 |
72 | 1 | 0 | 0 |
168 | 1 | 0 | 1 |
Setting the flush volume of the Hygiene function (C)
Flush volume (in litres) | Position of switch 8 |
|---|---|
3 | 0 |
7.5 | 1 |
Errors, faults and remedy
INFO!
In case of malfunctions, disconnect the model from the power supply and reconnect it after one minute.
Error | Cause | Solution |
|---|---|---|
The WC does not flush. | The supply voltage has failed. | Check the power supply. |
The cistern is not yet completely full. | Wait until the cistern is sufficiently full. | |
There is no water in the cistern. The corner valve is closed. | Open the corner valve. | |
The control is defective. | Replace the control. | |
The plugs of control and flush plate have not been connected. | Establish the plug connection. Mounting the flush plate | |
The WC flush runs through. | The seal at the filling valve is dirty or damaged. | Check the seal, replace if necessary. |
The seal at the drain valve is dirty or damaged. | Check the seal, replace if necessary. |
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.
Electronic components and batteries must not be put in the domestic waste but must be disposed of appropriately in conformity with the WEEE guideline 2012/19/EU.