Viega Eco Plus sink basin element
for Keramag sink basin model 201680,
sink basin for faeces, flush plates Visign
Year built (from): | 01-12-11 |
Trade mark rights exist for this document, further information can be found at viega.com/legal .
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
Consumers
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
This symbol warns against possible life-threatening injury.
This symbol warns against possible serious injury.
This symbol warns against possible injury.
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards .
Scope / Notice | Regulations applicable in Germany |
---|---|
suitable masonry walls | EN 1996‑1‑1 |
suitable concreted walls | DIN 1045 |
suitable support profiles | DIN 18183 |
Scope / Notice | Regulations applicable in Germany |
---|---|
Fulfilled noise protection requirements | DIN 4109 |
Fulfilled noise protection requirements | DIN 4109 (additional sheet 2) |
Fulfilled noise protection requirements | VDI 4100 SSt I-SSt II |
The Viega Eco Plus sink basin element is suitable for mounting on masonry wall constructions and stud frames pursuant to the regulations in section Regulations from section: Fields of application / Mounting conditions .
The shower element is compatible with the Keramag sink basin model 201680.
The drain valve set is suitable for the conversion to a flush plate from the Visign for Style or Visign for More series. The drain valve set consists of the drain valve with drain valve seat and bow, an actuating mechanism (dual-flush function) and an actuating rod set. The new fixing panel can be used after the installation of the drain valve set.
Product |
---|
Standard |
Visign for Style |
Visign for More |
Visign for Care sensitive |
Visign for More sensitive |
Visign for Public |
Name | Model |
---|---|
Flush plate Standard 1 | 8180.1 |
Flush plate Visign for Style 10 | 8315.1 |
Flush plate Visign for Style 11 | 8331.1 |
Flush plate Visign for Style 12 | 8332.1 |
Flush plate Visign for Style 12 | 8332.4 |
Flush plate Visign for Style 13 | 8333.1 |
Flush plate Visign for Style 14 | 8334.1 |
Functional unit | 8332.3 |
Flush plate Visign for More 100 | 8352.1 |
Flush plate Visign for More 101 | 8351.1 |
Flush plate Visign for More 102 | 8353.1 |
Flush plate Visign for More 103 | 8355.1 |
Flush plate Visign for More 104 | 8354.1 |
Flush plate sensitive Visign for Care | 8352.21 |
Flush plate sensitive Visign for More 100 | 230 V 8352.11 |
Flush plate sensitive Visign for More 100 | 6.5 V 8352.12 |
Flush plate sensitive Visign for More 103 | 230 V 8355.11 |
Flush plate sensitive Visign for More 103 | 6.5 V 8355.12 |
Flush plate Visign for Public 1 | 8326.1 |
Flush plate Visign for Public 2 | 8327.1 |
Flush plate Visign for Public 5 | 8326.16 |
Flush plate Visign for Public 6 | 8326.15 |
Remote actuation Visign for Public 1 | 8326.21 |
Cover plate Visign for Public | 8326.9 |
The sink basin element complies with the noise insulation requirements specified in section Regulations from section: Sound protection .
The product has the following technical data:
Connection elbow |
---|
Adapter |
Fitting connection, pre-mounted corner valve on left |
DN 90 (depth-adjustable), made of PP |
eccentric DN 90/100 made of PP |
Rp ½ |
cistern |
---|
Small flush volume |
Large flush volume |
Concealed cistern 2H | Concealed cistern, actuation from front |
Factory setting | approx. 3 l |
Setting range | approx. 3–4 l |
Factory setting | approx. ca. 6 l |
Setting range | approx. 6–9 l |
Immediate re-flushing is possible at the factory settings.
Keramag Espital sink, wall-hung, 6 L with stainless steel folding grate, 490 mm projection
The fixing set model 8173 is required to secure.
A wall-mounted fitting is recommended for hygienic cleaning or the filling of containers.
The element is suitable for mounting on masonry wall constructions and support profiles pursuant to the regulations in section Regulations from section: Fields of application / Mounting conditions .
The element may only be mounted on even wall surfaces.
With the construction height, the marked height of the upper edge of the finished floor must be observed.
The following tools are required for mounting the sink basin element:
drill with 10 mm drill bit
ratchet with sockets: 13 mm / 17 mm
fork or ring spanner: 13 mm / 17 mm
Masonry and concreted walls
You should use a support bracket (model 8165) when mounting multiple sink basin elements with an interval of > 490 mm. Observe the instructions for use of the support bracket when mounting.
Determine and mark fixing points.
X1: 390 mm (model 8180.73)
X2: 440 mm (model 8173)
X3: 1600 mm
Drill holes.
Mount the fixing set with the fork spanner (size 13).
Align height of element.
Whilst doing so, observe the markings on the element.
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
The construction height must be determined exactly.
There are only limited possibilities available to remedy errors made during this assembly step,
Construction height
.
Set the installation depth of the element with the fork spanner (size 17).
Remove WC element and drill floor holes.
Attach element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
Set height of the crossbeam.
The crossbeam aids the installation of the wall-mounted fitting.
Double-clad element (2 x 12.5 mm).
The element can be inserted into the 50 mm and 75 mm support profiles.
Determine the fixing points.
Align element.
If necessary, adjust the pre-mounted foot depth from 75 mm to 50 mm: Pull out foot and turn by 90°.
Attach element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
Align height of element.
Whilst doing so, observe the markings on the element.
The construction height must be determined exactly.
There are only limited possibilities available to remedy errors made during this assembly step,
Construction height
.
Screw element together laterally with the support profiles.
Make water connections.
Set height of the crossbeam.
The crossbeam aids the installation of the wall-mounted fitting.
Double-clad element (2 x 12.5 mm).
Immediate re-flushing of the flush volume is possible at the factory settings.
The sink basin element is factory-set at a small flush volume of approx. 3 l. The small flush volume can be set continuously from approx. 3 l up to approx. 4 l.
Remove the drain valve from the concealed cistern.
Push the slide control on the side of the overflow pipe to the desired small flush volume:
Top position: approx. 3 l
Bottom position: approx. 4 l
The sink basin element is factory-set at a large flush volume of approx. 6 l. The large flush volume can be set continuously from approx. 6 l up to approx. 9 l.
Remove the drain valve from the concealed cistern.
Push the slide control below the drain valve to the desired large flush volume:
left: approx. 6 l
right: approx. 9 l
If there is not enough space when pressing the water connection, the water connection can be pulled out to the side.
Screw the ½ inch connector into the wall lead-in.
Counter with a fork spanner (SW 27).
Loosen plastic union nut.
Pull out wall lead-in.
Press connection.
Push wall lead-in back into the plastic clamp.
The position of the key surface (SW 25) must be up or down.
The clicking into the groove signals the correct position.
Re-tighten the union nut.
Loosen (SW 19) flexible hose onto the filling valve.
Open corner valve.
Flush pipeline.
Close corner valve.
Re-mount (SW 19) the flexible hose onto the filling valve.
Loosen (SW 19) flexible hose onto the corner valve.
Unscrew plastic union nut.
Pull the corner valve inwards out of the wall lead-in.
Remove plastic union nut.
Remove the wall lead-in inwards.
Loosen the closing cap on the left-hand upper side of the concealed cistern.
Close opening on the side with the closing cap.
Push wall lead-in from inside into the upper opening.
Insert the corner valve back into the wall lead-in.
Screw plastic union nut back onto wall lead-in.
Re-mount (SW 19) the flexible hose onto the corner valve.
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.